FAQs

Can I somehow export the project?

Written by Vasilis Zagkanas
Updated this week

Can you see my project online?

Written by Vasilis Zagkanas
Updated this week

What do the capacitance results actually mean?

Written by Vasilis Zagkanas
Updated this week

I have gotten to the analysis part, but it fails at 10%.

Written by Vasilis Zagkanas
Updated this week

How do I see details from the progress of my analysis?

Written by Vasilis Zagkanas
Updated this week

Why my projects are submitted, but not in progress?

Written by Vasilis Zagkanas
Updated this week

Can I close the chrome tabs to run simulation? Or should let them open until it is done?

Written by Vasilis Zagkanas
Updated this week

About the shielding, do we mean it is connected to ground?

Written by Vasilis Zagkanas
Updated this week

How do you specify which layer the tracks and the shield element go on?

For example, I have set up two test tracks with an outline, and I want to place a shield underneath the tracks.

Written by Vasilis Zagkanas
Updated this week

What is the simplest way to simulate the capacitance across some PCB tracks?

Written by Vasilis Zagkanas
Updated this week

Does the pointer always touch the top side of the "first" layer (Layer 1) of the Stackup?

Written by Vasilis Zagkanas
Updated this week

Can I have more than one material forming the traces?

Written by Vasilis Zagkanas
Updated this week

Can I draw a Layout without importing a design?

Written by Vasilis Zagkanas
Updated this week

Do I have to specify the thickness of the conductive parts?

Written by Vasilis Zagkanas
Updated this week

Is it OK if a Via is not fully covered by the conductive layer it is connected to?

Written by Vasilis Zagkanas
Updated this week

How can I specify which side of the board the conductors are on?

Written by Vasilis Zagkanas
Updated this week

Do I need to change the electrical permittivity or the sheet resistance depending on the materials, like copper, ITO or Ag Nano?

Written by Vasilis Zagkanas
Updated this week

In order to get the mutual capacitance between two electrodes do I need to assign both as "active"?

Written by Vasilis Zagkanas
Updated this week

How can I set the ground in the Stackup?

Written by Vasilis Zagkanas
Updated this week

How can I assign a conductor as "active"?

Written by Vasilis Zagkanas
Updated this week

What does "active" mean in Capacitance Analysis ?

Written by Vasilis Zagkanas
Updated this week

Where can I set up the finger placement?

Written by Vasilis Zagkanas
Updated this week

What do I have to do before starting to run an Analysis?

Written by Vasilis Zagkanas
Updated this week

How is the finger simulated?

Written by Vasilis Zagkanas
Updated this week

Should I center every element at the (0,0) in the Layout canvas?

Written by Vasilis Zagkanas
Updated this week

The screen sometimes lags. How can I fix it?

Written by Vasilis Zagkanas
Updated this week

Which web browser should I use?

Written by Vasilis Zagkanas
Updated this week

GETTING STARTED WITH SENSE

Things you need to know about SENSE

Written by Christos Daskalou
Updated over a week ago

Key points

Usual mistakes done by our users and Known issues of the software

Written by Vasilis Zagkanas
Updated over a week ago

How to use Resources in SENSE

What do Cores and RAM mean in a simulation?

Written by Christos Daskalou
Updated over a week ago

How to prepare an importable dxf file

This article describes practices that will help a user work with .dxf sensor layout designs without any trouble

Written by Christos Daskalou
Updated over a week ago

What is a Capacitance Matrix

Description of Capacitance Matrix concept implemented to visualize capacitance values in Sense

Written by Vasilis Zagkanas
Updated over a week ago

What is the Equivalent Circuit Analysis

What you should know before you start using the Equivalent Circuit extraction tool

Written by Christos Daskalou
Updated over a week ago

How does a controller work

How does the charge transfer acquisition method work

Written by Christos Daskalou
Updated over a week ago